Description
OMPHobby M2 EVO swash leveling tool has been specially designed and printed by OriginHobbies to make it very easy for you to level the swash plate of your M2 or M2 EVO helicopter. No need to remove the head and links. It allows you to have a level swash plate and zero pitch when setting the SERVO center in the Flybarless controller settings.
NOTE: This tool is provided free with every M2 Helicopter (V2/EXP/EVO) purchased from our store!
Usage instructions
- Go to SERVO setting in the Flybarless controller.
- Increase the height of the swash plate by using Elevator, Aileron and Rudder stick inputs so swash leveling tool can fit under the swash plate.
- Slide the swash leveling tool below the swash plate from the front of the helicopter. Make sure it is sitting flat on the bearing block.
- Slowly lower the height of the swash plate by using Elevator, Aileron and Rudder stick inputs till the swash plate is sitting flush on the swash leveling tool.
- Verify that the blade pitch is zero. You can do that by folding the blades to be perpendicular to the blade grips and making sure that both blade edges are parallel to each other when viewing from the side. See above picture.
- IMPORTANT: Move the collective pitch stick to positive before coming out of the SERVO setting so the swash plate does not press excessively on the swash leveling tool and damage the servos.
- Enter PITCH setting. (press SET button once)
- Remove the swash leveling tool from the front.
- Save controller settings. (press and hold SET button for few seconds till it exits setup mode)
- Congratulations! You now have a perfectly level swash plate 🙂
EN 
FI 
SV 
DA 
DE 
FR
Daniel Van Halle (verified owner) –
Absolutely fantastic piece of kit!
A lot better then the original, aluminium one that comes together with the EVO.
Real handy swash leveller for the EVO!
Ingmar Koch (verified owner) –
Works as expected, great Tool.
Kari (verified owner) –
Nykyään ei saa hyödyllistä ilmaiseksi! Nämä saa kopun mukana lahjana 🤩
Brian (verified owner) –
Haven’t used it but good to have one
Giuseppe Nodari (verified owner) –
Top bene molto preciso
Patrik Johansson (verified owner) –
Grymt att få med detta. Enkelt att få en plan swashplatta med programmet i FBL enheten på helikoptern.
Johnny Johansson (verified owner) –
Tackar så mycket 🙏🙏
Anton (verified owner) –
Snabb frakt bra service
ANDREAS K. (verified owner) –
Swash leveling tool is good
Jaakko M. (verified owner) –
Very nice touch to add this so it will be ready to use when it is needed.
Volcmar (verified owner) –
Nice service to have
Ralf (verified owner) –
GREAT GIFT FROM OriginHobbies! Useful and functional as intended.
JESUS GONZALO (verified owner) –
Necessary tool that is free
Felix (verified owner) –
cooles Einstelltool 🙂
Christian von Schmidt (verified owner) –
Danke! Hilft sehr beim einstellen.
Ian S. (verified owner) –
Handy little Swashplate leveller.
Rudolph Franken (verified owner) –
Easy to have that there I thought to adjust.. there was also one in the Set and I didn’t know that
Balázs (verified owner) –
Pretty nice gift, print quality is good.
Roberto Dell’Acqua (verified owner) –
Always useful and handy
Ralf (verified owner) –
Hilfreiches Tool was ich aber noch nicht benutzt habe bzw. benutzen musste dank der perfekten Einstellung durch OriginHobbies bei der Auslieferung meines RC Helis.
Giuseppe Nodari (verified owner) –
Top tutto perfetto……
Rafal (verified owner) –
Quality 3D printed tool.
Valentin Nouet (verified owner) –
Pas tester pour le moment.
Gianluca Samore (verified owner) –
Nice surprise to find it free in the Rtf set.
I had no chances to use it yet, but is good print quality
Patrik G. (verified owner) –
Nice tool for perfect setup
Anonymous (verified owner) –
Works well with M2 Evo
Anonymous (verified owner) –
A gift from the sellers, thx
Thomas (verified owner) –
Zweckdienlich aber nicht schön. Alu wäre toll.
Petr Paril (verified owner) –
Funguje jak má …………………
kaistrozyk (verified owner) –
Tried the original OMP aluminum cnc tool and this 3D-Printed tool, I prefer thisone over the original! Both do their Job but thisone is mor precise and better to handle.
Tobias Ramm (verified owner) –
Gut zuhaben, wurde noch nicht gebraucht.
Timo (verified owner) –
Works perfectly with OMPHobby M2 Evo
Van Daele Claude (verified owner) –
Excellent tool for the M2
Mike (verified owner) –
OMPHobby M2 swash leveling tool sehr, sehr praktisch