La description
OMPHobby M2 EVO swash leveling tool has been specially designed and printed by OriginHobbies to make it very easy for you to level the swash plate of your M2 or M2 EVO helicopter. No need to remove the head and links. It allows you to have a level swash plate and zero pitch when setting the SERVO center in the Flybarless controller settings.
NOTE: This tool is provided free with every M2 Helicopter (V2/EXP/EVO) purchased from our store!
Usage instructions
- Go to SERVO setting in the Flybarless controller.
- Increase the height of the swash plate by using Elevator, Aileron and Rudder stick inputs so swash leveling tool can fit under the swash plate.
- Slide the swash leveling tool below the swash plate from the front of the helicopter. Make sure it is sitting flat on the bearing block.
- Slowly lower the height of the swash plate by using Elevator, Aileron and Rudder stick inputs till the swash plate is sitting flush on the swash leveling tool.
- Verify that the blade pitch is zero. You can do that by folding the blades to be perpendicular to the blade grips and making sure that both blade edges are parallel to each other when viewing from the side. See above picture.
- IMPORTANT: Move the collective pitch stick to positive before coming out of the SERVO setting so the swash plate does not press excessively on the swash leveling tool and damage the servos.
- Enter PITCH setting. (press SET button once)
- Remove the swash leveling tool from the front.
- Save controller settings. (press and hold SET button for few seconds till it exits setup mode)
- Congratulations! You now have a perfectly level swash plate 🙂
EN 
FI 
SV 
DA 
DE 
FR
Daniel Van Halle (client confirmé) –
Absolutely fantastic piece of kit!
A lot better then the original, aluminium one that comes together with the EVO.
Real handy swash leveller for the EVO!
Ingmar Koch (client confirmé) –
Works as expected, great Tool.
Kari (client confirmé) –
Nykyään ei saa hyödyllistä ilmaiseksi! Nämä saa kopun mukana lahjana 🤩
Brian (client confirmé) –
Haven’t used it but good to have one
Giuseppe Nodari (client confirmé) –
Top bene molto preciso
Patrik Johansson (client confirmé) –
Grymt att få med detta. Enkelt att få en plan swashplatta med programmet i FBL enheten på helikoptern.
Johnny Johansson (client confirmé) –
Tackar så mycket 🙏🙏
Anton (client confirmé) –
Snabb frakt bra service
ANDREAS K. (client confirmé) –
Swash leveling tool is good
Jaakko M. (client confirmé) –
Very nice touch to add this so it will be ready to use when it is needed.
Volcmar (client confirmé) –
Nice service to have
Ralf (client confirmé) –
GREAT GIFT FROM OriginHobbies! Useful and functional as intended.
JESUS GONZALO (client confirmé) –
Necessary tool that is free
Felix (client confirmé) –
cooles Einstelltool 🙂
Christian von Schmidt (client confirmé) –
Danke! Hilft sehr beim einstellen.
Ian S. (client confirmé) –
Handy little Swashplate leveller.
Rudolph Franken (client confirmé) –
Easy to have that there I thought to adjust.. there was also one in the Set and I didn’t know that
Balázs (client confirmé) –
Pretty nice gift, print quality is good.
Roberto Dell’Acqua (client confirmé) –
Always useful and handy
Ralf (client confirmé) –
Hilfreiches Tool was ich aber noch nicht benutzt habe bzw. benutzen musste dank der perfekten Einstellung durch OriginHobbies bei der Auslieferung meines RC Helis.
Giuseppe Nodari (client confirmé) –
Top tutto perfetto……
Rafal (client confirmé) –
Quality 3D printed tool.
Valentin Nouet (client confirmé) –
Pas tester pour le moment.
Gianluca Samore (client confirmé) –
Nice surprise to find it free in the Rtf set.
I had no chances to use it yet, but is good print quality
Patrik G. (client confirmé) –
Nice tool for perfect setup
Anonyme (client confirmé) –
Works well with M2 Evo
Anonyme (client confirmé) –
A gift from the sellers, thx
Thomas (client confirmé) –
Zweckdienlich aber nicht schön. Alu wäre toll.
Petr Paril (client confirmé) –
Funguje jak má …………………
kaistrozyk (client confirmé) –
Tried the original OMP aluminum cnc tool and this 3D-Printed tool, I prefer thisone over the original! Both do their Job but thisone is mor precise and better to handle.
Tobias Ramm (client confirmé) –
Gut zuhaben, wurde noch nicht gebraucht.
Timo (client confirmé) –
Works perfectly with OMPHobby M2 Evo
Van Daele Claude (client confirmé) –
Excellent tool for the M2
Mike (client confirmé) –
OMPHobby M2 swash leveling tool sehr, sehr praktisch