La description
MSH Brain2 HD is a great value Flybarless controller for larger Electric, Nitro, Gasser with pro features like Governor, Rescue and Telemetry already available without extra cost. Made in Italy.
Caractéristiques
- Size (width x length x height): 29,6 x 37,7 x 22,3 mm
- Poids: 16,7 g
- 15 Connections:
9 Gold-plated servo type three pole JR/Futaba male connectors, with 11 signals connections configurable for:-
- 9output (7 PWM + TX for SYS + TX for on onboard USB), and/or 11 input (6 single PWM from RX, 1 RPM pulses + SAT1 +SAT2 + RX on SYS + RX on onboard USB) and 8 servo power bus connections
- 1 Power MPX connector controlled by a switch
- 1 Gold-plated servo type three pole male JR/Futaba connector for power switch
- 1 On board micro USB connector capable to power internally the Unit
- 1 SYS four poles JST connector (GND, TX, RX, +V) capable to power internally the unit or an external accessory (Wireless Dongle)
- 2 SAT three pole JST connectors with 3,3V output (2 input and/or 2 output)
-
- Serial input for every receiver Brand with very low latency method:
- Spektrum: New bidirectional SRXL v2 (with telemetry) / Bidirectional SRXL (with telemetry) / Unidirectional SRXL / DSM2 22mS / DSM2 11mS / DSMX 11mS / PPM / Remote RX
- Futaba: S.Bus2 (with telemetry) / S.Bus / PPM
- Jeti: EX-BUS (with telemetry) / UDI / PPM+ / PPM-
- Graupner: SUMD (with telemetry) / SUMO
- Multiplex: SRXL + MSB (with telemetry)
- FrSky: S.Bus + Smart.Port (with telemetry) / F.Port (with telemetry) / F.Port2 (with telemetry) / F.Bus (with telemetry) / S.Bus
- JR: X-Bus B
- Hitec: S.Bus
- RadioLink: S.Bus
- TBS: Crossfire (with telemetry) / S.Bus / PPM
- ELRS: Crossfire (with telemetry)
- FlySky: i-Bus (with telemetry)
- Governor:
For Electric, Nitro, Gasser
Governor rotor speed control range: 800-6500 RPM
Autorotation Bailout function (fast RPM recovery from a failed autorotation manoeuvre)
- Telemetry input:
From ESC on electric models:
Castle Creation
Hobbywing
Align
Scorpion
Kontronik
YGE
Spektrum
FrSky
OMPFrom Temperature sensors on Nitro / Gasser / Turbine models:
Jeti
FutabaFrom RPM Sensors:
All sensor brandPossibility to monitor separately also the RPM of the tail motor
From Variometer (Altitude, Vertical Speed):
Jeti on SAT2 connector
FrSky, Futaba, Robbe, Graupner sensors on BusQuality Of Signal (QOS) received:
For all receivers brandQuality of Servo Voltage input:
For all kind of Power input: ESC BEC, external/separate BEC, 2S Lipos/Li-Ion/Li-Fe/NiCd/NiMh, Backup Power Systems
- Telemetry output:
Spektrum, Futaba, Jeti, Graupner, Multiplex, OpenTX, EdgeTX, Ethos, Crossfire, FlySky
- Power input:
Between 4,5V to 15V with one or two (redundant) lines from BEC or 2S Li-Po (7.4V) or 2S Li-Ion (7.4V) or 2S Li-Fe (6.6V) or 5/6/7 NiCd -NiMh
The direct current managed by the electronic switch located downstream of the MPX connector is 20A with short-term peaks up to 50A
- Outputs:
7 Servos/ESC outputs. Of which 5 are fully programmable from 50 to 560Hz (also for cyclic control)
- Auto Diagnosis at each power on:
With result by LED flashes
With result by initial Swashplate movements
- Diagnostic logs:
More than 50 different parameters can be recorded during flights
Vibrations are also logged during flights
More than 50 different types of Events are monitored and automatically logged during flights
- Already included “on board”:
Status LED
USB on board
- Parameters setup / regulation:
Via apps in English, Deutsch, François, Russian, Chinese, Italian, Spanish (with the possibility to add, edit, share other languages):
les fenêtres
MAC (with emulators)
Linux (with emulators)
Android
iOSVia “Integrations” menu:
Spektrum
Jeti
Graupner
OpenTX
EdgeTX
Ethos
Crossfire (ELRS/TBS)Via dedicated transmitters channels (dials):
In addition to the radio channel dedicated to tail gain, up to other three radio channels can be assigned to one of the 51 internal parameters of the unitSwashplates:
90°
120°
135°
140°
4 servos
Tandem rotorsMounting positions:
Up to 16 different possible mounting positions on the model
Included in the package:
- 1x Brain2 HD
- 1x Servo cable for serial RX connection
- 1x Cable red/black + plug MPX
- 1x Switch black + cable + plug
- 2x Double-sided adhesive
- 1x ‘Safety Notes’ leaflet
Updates can be handled automatically for free by the software after first installation.
Visit the release notes under “info” menu of the software after each update.
EN 
FI 
SV 
DA 
DE 
FR
Bruno Hansen (client confirmé) –
super godt, hurtig levering