{"id":4457,"date":"2022-08-20T09:42:31","date_gmt":"2022-08-20T07:42:31","guid":{"rendered":"http:\/\/originhobbies.com\/?page_id=4457"},"modified":"2024-05-26T21:23:24","modified_gmt":"2024-05-26T19:23:24","slug":"radiomaster-zorro-setup-for-omphobby-m2-evo-and-m1-evo-edgetx","status":"publish","type":"page","link":"https:\/\/originhobbies.com\/fi\/radiomaster-zorro-setup-for-omphobby-m2-evo-and-m1-evo-edgetx\/","title":{"rendered":"Radiomaster Zorro setup for OMPHobby M2 EVO and M1 EVO (EdgeTX)"},"content":{"rendered":"

This guide will show you how to setup your Radiomaster Zorro for your OMPHobby M2 EVO or M1 EVO Helicopter.<\/p>\n\n\n\n

If you purchased a RTF Combo or Zorro Radio from us, this setup is already done for you.<\/p>\n\n\n\n

EdgeTX model configuration files<\/h3>\n\n\n\n

Configuration File<\/h4>\n\n\n\n

Download OriginHobbies Zorro EdgeTX Model Configuration File.<\/a><\/strong> (right click and Save as)<\/p>\n\n\n\n

It can be used with both EdgeTX Companion software. It contains all the models listed below.<\/p>\n\n\n\n

Model names in Configuration file<\/h4>\n\n\n\n
Model Name<\/th>Model<\/th>Vastaanotin<\/th>Protocol<\/th><\/tr><\/thead>
EVO FUT<\/td>M1 EVO & M2 EVO<\/td>Built-in \/ OSHM2055<\/a><\/td>S-FHSS<\/td><\/tr>
EVO DSM<\/td>M1 EVO & M2 EVO<\/td>DSM nano Satellite<\/a><\/td>DSM \/ DSM2 \/ DSMx<\/td><\/tr>
EVO OMP<\/td>M1 EVO & M2 EVO<\/td>Built-in<\/td>OMP<\/td><\/tr>
EVO XSR<\/td>M1 EVO & M2 EVO<\/td>Frsky R-XSR<\/a> \/ Archer plus RS mini<\/a><\/td>FrskyX2 D16 (EU-LBT)<\/td><\/tr>
EVO R81<\/td>M1 EVO & M2 EVO<\/td>Radiomaster R81<\/a><\/td>Frsky D8<\/td><\/tr><\/tbody><\/table>
Models in OriginHobbies Zorro Configuration file<\/figcaption><\/figure>\n\n\n\n

Loading Models from configuration file to Radio<\/h4>\n\n\n\n
    \n
  1. Download and install Edge Companion tool<\/a> on PC\/Mac\/Linux.<\/li>\n\n\n\n
  2. Start the Companion tool.<\/li>\n\n\n\n
  3. In Settings->Settings->Radio Type ensure that “Radiomaster Zorro”<\/strong> is selected.<\/li>\n\n\n\n
  4. Power ON<\/strong> the Radio and Connect the Radio to USB port of your computer. Select “USB Storage mode<\/strong>“<\/li>\n\n\n\n
  5. Get the models from the Radio to Companion tool.
    Select Read\/write->Read current models from radio<\/strong>.<\/li>\n\n\n\n
  6. Open the OriginHobbies configuration file you downloaded from above. There are many models in the configuration file. Copy the models you need from OriginHobbies configuration window to your Radio’s configuration window.<\/li>\n\n\n\n
  7. Save the models from the Companion tool to the Radio.
    Select Read\/write->Write current models to radio<\/strong>.<\/li>\n\n\n\n
  8. Safely remove the USB disk drive.<\/li>\n\n\n\n
  9. Disconnect the Zorro from Computer’s USB port.<\/li>\n<\/ol>\n\n\n\n

    Receiver type<\/h3>\n\n\n\n

    Futaba \/ S-FHSS<\/h4>\n\n\n\n

    The helicopter supports one one SBUS<\/strong> port. You can connect a SBUS compatible receiver to this port. It will override the internal OMP receiver. e.g. OSHM2055 S-FHSS micro receiver<\/a> <\/p>\n\n\n\n

    Choose model EVO FUT<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td>Inverted<\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Throttle<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td>Inverted<\/td><\/tr>
    5<\/td>Stability mode (ON\/OFF)<\/td>Inverted<\/td><\/tr>
    6<\/td>Collective Pitch<\/td><\/td><\/tr><\/tbody><\/table>
    S-FHSS receiver channel map<\/figcaption><\/figure>\n\n\n\n

    DSM<\/h4>\n\n\n\n

    The helicopter supports one Spektrum DSM Satellite <\/strong>port. You can connect a Spektrum satellite receiver to this port. e.g. DSM2 \/ DSMX nano Satellite receiver with bind button<\/a>.<\/p>\n\n\n\n

    Choose model EVO DSM<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td>Inverted<\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Throttle<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td>Inverted<\/td><\/tr>
    5<\/td>Stability mode (ON\/OFF)<\/td><\/td><\/tr>
    6<\/td>Collective Pitch<\/td><\/td><\/tr><\/tbody><\/table>
    DSM Receiver channel map<\/figcaption><\/figure>\n\n\n\n

    OMP protocol<\/h4>\n\n\n\n

    OMPHobby M2 EVO and M1 EVO OMP comes with built-in receiver that supports OMP Protocol. In OMP Protocol, the throttle curve is fixed in the helicopter and cannot be adjusted at the Transmitter Radio. OMP protocl supports telemetry for Helicopter battery voltage. Normal, Idle-up1 and Idle-up2 flight modes are assigned by a switch on the Radio transmitter.<\/p>\n\n\n\n

    Choose model EVO OMP<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td><\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Collective Pitch<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td><\/td><\/tr>
    5<\/td>Throttle Hold<\/td><\/td><\/tr>
    6<\/td>Flight mode (Normal\/Idle1\/Idle2)<\/td><\/td><\/tr>
    7<\/td>Stability mode (ON\/OFF)<\/td>Inverted<\/td><\/tr><\/tbody><\/table>
    OMP Receiver channel map<\/figcaption><\/figure>\n\n\n\n

    <\/p>\n\n\n\n

    Frsky D16 protocol (Archer Plus RS mini & R-XSR)<\/h4>\n\n\n\n

    The Archer Plus RS mini<\/a> receiver is perfect for M1 and M2 helicopters due to its compact size. It even comes with the correct adapter cable.<\/p>\n\n\n\n

    Note that R-XSR receiver supports 2 modes on SBUS out pin (SBUS mode and CPPM mode). This pin should be in SBUS mode to work with M1\/M2 helicopter. The blue LED is turned ON for SBUS mode and OFF for CPPM mode. Press the bind button for 4 seconds to switch between the two modes.<\/p>\n\n\n\n

    Choose model EVO XSR<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td><\/td><\/tr>
    2<\/td>Elevator<\/td>Inverted<\/td><\/tr>
    3<\/td>Throttle<\/td>Inverted<\/td><\/tr>
    4<\/td>Rudder<\/td><\/td><\/tr>
    5<\/td>Stability mode (ON\/OFF)<\/td><\/td><\/tr>
    6<\/td>Collective Pitch<\/td>Inverted<\/td><\/tr><\/tbody><\/table>
    R-XSR receiver channel map<\/figcaption><\/figure>\n\n\n\n

    Radio switch Layout<\/h3>\n\n\n
    \n
    \"\"
    Zorro Switch Layout<\/figcaption><\/figure>\n<\/div>\n\n\n
    Function<\/th>Switch<\/th><\/tr><\/thead>
    Throttle hold fail-safe<\/td>SE<\/td><\/tr>
    Throttle hold<\/td>SC<\/td><\/tr>
    Flight mode (Normal, Idle-up1, Idle-up2)<\/td>SB<\/td><\/tr>
    Rescue switch<\/td>SA (button)<\/td><\/tr>
    Attitude hold (auto level) ON\/OFF<\/td>SF<\/td><\/tr>
    Volume control<\/td>S2 knob<\/td><\/tr><\/tbody><\/table>
    Zorro switch assignment<\/figcaption><\/figure>\n\n\n\n

    Other functions<\/h3>\n\n\n\n
      \n
    • Flight timer: 4.5 mins, Haptic countdown at 10 seconds<\/li>\n\n\n\n
    • To reset flight timer, both Throttle hold switches should be in Throttle hold.<\/li>\n\n\n\n
    • Voice call on Throttle cut, Throttle active, Flight modes and Stability mode.<\/li>\n<\/ul>\n\n\n\n

      Binding and pre-flight Check<\/h3>\n\n\n\n

      Binding<\/h4>\n\n\n\n
        \n
      1. Ensure batteries of your Helicopter and Transmitter are sufficiently charged<\/li>\n\n\n\n
      2. It is a good idea to remove the main and tail blades of the helicopter to prevent any injury if motors start accidentally.<\/li>\n\n\n\n
      3. Choose the correct model on the Zorro Transmitter.<\/li>\n\n\n\n
      4. Ensure throttle hold is engaged.<\/li>\n\n\n\n
      5. Plug in the battery into the Helicopter and wait for beeps.<\/li>\n\n\n\n
      6. Press and hold BIND<\/strong> button on helicopter. Blue LED<\/mark> will start flashing. Release the BIND<\/strong> button.<\/li>\n\n\n\n
      7. On the Radio, go to Model setup. Press MDL<\/strong> button followed by PAGE><\/strong> button<\/li>\n\n\n\n
      8. Scroll down to INTERNAL RF<\/strong> section<\/li>\n\n\n\n
      9. Check that the correct RF Protocol is selected in Type<\/strong> ja Subtype<\/strong>. If not you have chosen the wrong model.<\/li>\n\n\n\n
      10. Highlight BND<\/strong> on screen and press Enter (press the Scroll wheel).<\/li>\n\n\n\n
      11. During binding process, the Blue LED<\/mark> will flash rapidly<\/strong>. Once binding is complete the Blue LED<\/mark> will be steady<\/strong>.<\/li>\n\n\n\n
      12. Press RTN<\/strong> on the Zorro to exit Bind mode.<\/li>\n<\/ol>\n\n\n
        \n
        \"\"
        Binding<\/figcaption><\/figure>\n<\/div>\n\n\n

        Pre-flight check<\/h4>\n\n\n\n
          \n
        • The Red LED<\/mark> indicates Auto-level<\/strong> mode status.
          Red LED<\/mark> blinking<\/strong> = Auto-level OFF<\/strong>.
          Red LED<\/mark> steady<\/strong> = Auto-level ON<\/strong>.
          Toggle auto-level switch and see it is switching between Auto-level<\/strong> ON<\/strong> ja OFF<\/strong>.<\/li>\n\n\n\n
        • Keep Auto-level OFF<\/strong>.<\/li>\n\n\n\n
        • Move the aileron\/elevator<\/strong> sticks and check that the swash plate is moving correctly (left-right<\/strong> ja front-back<\/strong>)<\/li>\n\n\n\n
        • Move the collective<\/strong> pitch stick and check that the swash plate is moving correctly (up<\/strong> & down<\/strong>)<\/li>\n\n\n\n
        • Disengage<\/strong> both throttle hold and throttle hold fail safe<\/strong> switches, give some collective and check that main rotor is spinning<\/strong>.<\/li>\n\n\n\n
        • Engage<\/strong> any one throttle hold<\/strong> and check that main rotor stops<\/strong>.<\/li>\n\n\n\n
        • Engage both<\/strong> throttle holds and check that flight timer resets.<\/li>\n\n\n\n
        • Now you can put the rotor blades back on and do a test flight. Good Luck!<\/li>\n<\/ul>\n\n\n\n

          Model Customization<\/h3>\n\n\n\n

          You can customize the model configuration as per your linking. Please refer to explanation of different settings.<\/p>\n\n\n\n

          Switch Assignment<\/h4>\n\n\n\n

          To change the switch assignments Navigate to Model->Input Page<\/p>\n\n\n

          \n
          \"\"
          Model Input Page<\/figcaption><\/figure>\n<\/div>\n\n\n

          Scroll to the Function whose switch you want to change. e.g. To change rescue mode switch scroll to Rsq input. Press and hold the Scroll wheel and select EDIT.<\/p>\n\n\n

          \n
          \"\"
          Changing Rescue mode switch<\/figcaption><\/figure>\n<\/div>\n\n\n

          Scroll to Source and press the scroll wheel button. Then scroll till you find your desired switch. Press the scroll wheel button to confirm.<\/p>\n\n\n\n

          Throttle curves<\/h4>\n\n\n\n

          For OMP Protocol, there are no throttle curves on the Radio Transmitter as throttle curve is fixed inside the Helicopter. For other protocols, the below curves are used.<\/p>\n\n\n\n

          Curve<\/th>Curve name<\/th>Function<\/th><\/tr><\/thead>
          CV2<\/td>TCn<\/td>Throttle curve for Normal mode<\/td><\/tr>
          CV3<\/td>TC1<\/td>Throttle curve for Idle-up 1<\/td><\/tr>
          CV4<\/td>TC2<\/td>Throttle curve for Idle-up 2<\/td><\/tr><\/tbody><\/table>
          Throttle curves<\/figcaption><\/figure>\n\n\n\n

          <\/p>\n\n\n\n

          Pitch curves<\/h4>\n\n\n\n
          Curve<\/th>Curve name<\/th>Function<\/th><\/tr><\/thead>
          CV6<\/td>PCn<\/td>Collective pitch curve for Normal mode<\/td><\/tr>
          CV7<\/td>PC1<\/td>Collective pitch curve for Idle-up 1<\/td><\/tr>
          CV8<\/td>PC2<\/td>Collective pitch curve for Idle-up 2<\/td><\/tr><\/tbody><\/table>
          Pitch curves<\/figcaption><\/figure>\n\n\n\n

          <\/p>\n\n\n\n

          Config file Revision history<\/h3>\n\n\n\n
          v3.5: 2023-02-19
          - Added new model \"720 OMP\" for OMP S720 and T720 Airplanes

          v3.4: 2024-01-29
          - OMP: Reduced Normal mode pitch curve to 80 to be less aggressive as it also controls throttle.

          v3.3: 2023-07-16
          - All: Moved TH2 to button SD to free up switch SE for dual-rates.
          - All: Added dual rate function on switch SE.
          - All: Added Receiver ID.
          - Remove R81 model

          v3.2: 2023-06-08
          -Added backlight control via S1 Knob

          v3.1: 2023-05-16
          -Fixed rotary knob direction

          v3.0: 2023-05-10
          -All: added back deadband curve for Elevator and Aileron

          v2.9: 2023-03-30
          -R81: Added model for Radiomaster R81 nano receiver

          v2.8: 2023-03-28
          -R-XSR: Added model for R-XSR receiver. Added telemetry screen for VFAS, Curr, mAh, RxBt and RSSI

          v2.7: 2023-03-14
          -All: updated sound track for fm1, fm2, 3d and stable mode.

          v2.6: 2023-01-12
          -FUT\/DSM: Change normal mode throttle curve to 0,5,5,5,5. We want governor to be engaged througout except full negative.
          -OMP: Added RSSI to telemetry screen

          v2.5: 2022-12-02
          -All: Add Rescue mode on sound.
          https:\/\/github.com\/EdgeTX\/edgetx-sdcard-sounds\/blob\/main\/SOUNDS\/en\/rscmon.wav?raw=true

          v2.4: 2022-11-30
          -All: Added 15% expo to Aileron, Elevator, Rudder inputs to tame down at center stick.
          -EVO OMP: Adjusted Normal mode Pitch Curve for -100, 0, 100. Heli has internal throttle curve.
          -EVO OMP: Added telemetry screen for Heli battery voltage.

          v2.3: 2022-11-20
          -EVO OMP: Adjusted Normal mode Pitch Curve for a bit more punch. -100,0,85

          v2.2: 2022-10-14
          -EVO FUT, DSM, OMP: Removed PCs curve from pitch mix so pitch doesn't change when switching to stability mode.
          -EVO OMP: Tamed down Normal mode Pitch Curve so throttle and pitch are more manageable.

          v2.1: 2022-10-09
          -EVO FUT & DSM: Fix Pitch channel mix. Use Replace instead of Add for Idle1 & Idle2

          v2.0: 2022-10-07
          -EVO FUT & EVO DSM: Streamlined Input, Mixes and Logical Switches so user can easily change switch function just from Input page.
          -EVO DSM: Fixed inverted Stability mode by reversing channel.
          -EVO FUT, DSM, OMP: all use same monitor screen
          -EVO OMP: Lowered low and critical signal warnings to 25, 15.

          v1.5: 2022-10-05
          -EVO OMP: Added Rescue mode support to OMP config.
          -EVO OMP: Streamlined Input, Mixes and Logical Switches so user can easily change switch function just from Input page.
          -Flight timer increased from 3:00 to 4:30

          v1.4: 2022-09-29
          -Removed deadband curve mix from Aileron and Elevator as it is too twitchy at the center.

          v1.3: 2022-09-28
          -Update throttle curve FUT\/DSM from 0-5-10 to 0-8-15
          -Changed flight timer from 3 mins to 4 mins.

          v1.2: 2022-09-02
          -Fixed failsafe warning at startup for all OMP modesl
          -Fixed OMP model protocol and channel direction

          v1.1: 2022-08-20
          -Used CP1 curve instead of CPL curve for collective pitch for Stability mode
          -Added EVO OMP model for OMP protocol

          v1: 2022-08-19
          -Initial version<\/pre>","protected":false},"excerpt":{"rendered":"
          This guide will show you how to setup your Radiomaster Zorro for your OMPHobby M2 EVO or M1 EVO Helicopter. If you purchased a RTF Combo or Zorro Radio from us, this setup is already done for you. EdgeTX model configuration files Configuration File Download OriginHobbies Zorro EdgeTX Model Configuration File. (right click and Save […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_eb_attr":"","footnotes":""},"class_list":["post-4457","page","type-page","status-publish","hentry"],"jetpack_sharing_enabled":true,"jetpack_shortlink":"https:\/\/wp.me\/Ph9vxs-19T","_links":{"self":[{"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/pages\/4457","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/comments?post=4457"}],"version-history":[{"count":0,"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/pages\/4457\/revisions"}],"wp:attachment":[{"href":"https:\/\/originhobbies.com\/fi\/wp-json\/wp\/v2\/media?parent=4457"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}