{"id":10075,"date":"2024-01-27T12:54:33","date_gmt":"2024-01-27T10:54:33","guid":{"rendered":"http:\/\/originhobbies.com\/?page_id=10075"},"modified":"2025-10-22T11:27:00","modified_gmt":"2025-10-22T09:27:00","slug":"radiomaster-pocket-radio-setup-for-omphobby-m1-m2-evo-edgetx","status":"publish","type":"page","link":"https:\/\/originhobbies.com\/de\/radiomaster-pocket-radio-setup-for-omphobby-m1-m2-evo-edgetx\/","title":{"rendered":"Radiomaster Pocket Radio setup for OMPHobby M1, M2 (EdgeTX)"},"content":{"rendered":"

This guide will show you how to setup your Radiomaster Pocket or any EdgeTX \/ OpenTX Multi-protocol radio for your OMPHobby M1, M2 EVO or M2 V3 Helicopter.<\/p>\n\n\n\n

If you purchased a RTF Combo or Pocket Radio from us, this setup is already done for you.<\/p>\n\n\n\n

ACHTUNG:<\/strong> TX12 C2500 supports the following radio protocols (Futaba S-FHSS, OMP, Frsky D16 \/ D8 \/ X \/ X2, Esky, Corona, Hitec, RadioLink, Graupner HoTT, Skyartec)<\/p>\n\n\n\n

EdgeTX model configuration files<\/h3>\n\n\n\n

Configuration File<\/h4>\n\n\n\n

Download OriginHobbies Pocket EdgeTX Model Configuration File<\/a>.<\/strong> (right click and Save as)<\/p>\n\n\n\n

The Configuration contains all the models listed below. Please see end of this page for Revision history of the Configuration files.<\/p>\n\n\n\n

Model names in Configuration file<\/h4>\n\n\n\n
Model Name<\/th>Model<\/th>Empf\u00e4nger<\/th>Protocol<\/th><\/tr><\/thead>
EVO FUT<\/td>M1 EVO & M2 EVO<\/td>Built-in \/ OSHM2055<\/a><\/td>S-FHSS<\/td><\/tr>
EVO OMP<\/td>M1 EVO & M2 EVO<\/td>Built-in<\/td>OMP<\/td><\/tr>
OFS3 FUT<\/td>M2 V3 & M2 MK2<\/td>OSHM2055<\/a><\/td>S-FHSS<\/td><\/tr><\/tbody><\/table>
Models in OriginHobbies Pocket configuration file<\/figcaption><\/figure>\n\n\n\n

Loading Models from configuration file to Radio<\/h4>\n\n\n\n
    \n
  1. Download and install Edge Companion tool<\/a> on PC\/Mac\/Linux.<\/li>\n\n\n\n
  2. Start the Companion tool.<\/li>\n\n\n\n
  3. Power ON<\/strong> the Radio and Connect the Radio to USB port of your computer. Select “USB Storage mode<\/strong>“<\/li>\n\n\n\n
  4. Get the models from the Radio to Companion tool.
    Select Read\/write->Read current models from radio<\/strong>.<\/li>\n\n\n\n
  5. Open the OriginHobbies configuration file you downloaded from above. There are many models in the configuration file. Copy the models you need from OriginHobbies configuration window to your Radio’s configuration window.<\/li>\n\n\n\n
  6. Save the models from the Companion tool to the Radio.
    Select Read\/write->Write current models to radio<\/strong>.<\/li>\n\n\n\n
  7. Safely remove the USB disk drive.<\/li>\n\n\n\n
  8. Disconnect USB.<\/li>\n<\/ol>\n\n\n\n

    Receiver type<\/h3>\n\n\n\n

    OMP protocol<\/h4>\n\n\n\n

    OMPHobby M2 comes with built-in receiver that supports OMP Protocol. In OMP Protocol, the throttle curve is fixed in the helicopter and cannot be adjusted at the Transmitter Radio. OMP protocl supports telemetry for Helicopter battery voltage. Normal, Idle-up1 and Idle-up2 flight modes are assigned by a switch on the Radio transmitter.<\/p>\n\n\n\n

    Choose model EVO OMP<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td><\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Collective Pitch<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td><\/td><\/tr>
    5<\/td>Throttle Hold<\/td><\/td><\/tr>
    6<\/td>Flight mode (Normal\/Idle1\/Idle2)<\/td><\/td><\/tr>
    7<\/td>Stability mode (ON\/OFF)<\/td>Inverted<\/td><\/tr><\/tbody><\/table>
    OMP Receiver channel map<\/figcaption><\/figure>\n\n\n\n

    EVO FUT (S-FHSS)<\/h4>\n\n\n\n

    The helicopter supports one one SBUS<\/strong> port. You can connect a SBUS compatible S-FHSS receiver to this port. It will override the internal OMP receiver. e.g. OSHM2055 S-FHSS micro receiver<\/a><\/p>\n\n\n\n

    Choose model EVO FUT<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td>Inverted<\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Throttle<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td>Inverted<\/td><\/tr>
    5<\/td>Stability mode (ON\/OFF)<\/td>Inverted<\/td><\/tr>
    6<\/td>Collective Pitch<\/td><\/td><\/tr><\/tbody><\/table>
    S-FHSS receiver channel map<\/figcaption><\/figure>\n\n\n\n

    NOTE: If you are not using S-FHSS (Futaba) receiver on the SBUS port then choose the correct the RF Protocol<\/strong> und Protocol Sub Type<\/strong> in your TX16S Model Setup -> Internal RF<\/strong><\/p>\n\n\n

    \n
    \"\"
    RF Protocol and Sub Type<\/figcaption><\/figure>\n<\/div>\n\n\n

    OFS3 FUT (S-FHSS)<\/h4>\n\n\n\n

    The OSF3 controller on M2 V3 and M2 MK2 supports one one SBUS<\/strong> port. You can connect a SBUS compatible S-FHSS receiver to this port. e.g. OSHM2055 S-FHSS micro receiver<\/a><\/p>\n\n\n\n

    Choose model OFS3 FUT<\/strong> from the configuration file.<\/p>\n\n\n\n

    Channel<\/th>Function<\/th>Direction<\/th><\/tr><\/thead>
    1<\/td>Aileron<\/td><\/td><\/tr>
    2<\/td>Elevator<\/td><\/td><\/tr>
    3<\/td>Throttle<\/td><\/td><\/tr>
    4<\/td>Rudder<\/td><\/td><\/tr>
    5<\/td>Stability mode (ON\/OFF)<\/td><\/td><\/tr>
    6<\/td>Collective Pitch<\/td><\/td><\/tr><\/tbody><\/table>
    OFS3 S-FHSS receiver channel map<\/figcaption><\/figure>\n\n\n\n

    Radio switch Layout<\/h3>\n\n\n
    \n
    \"\"
    Pocket Switch Layout<\/figcaption><\/figure>\n<\/div>\n\n\n
    Function<\/th>Switch<\/th><\/tr><\/thead>
    Throttle hold<\/td>SD<\/td><\/tr>
    Flight mode (\u2191<\/em>Normal, –<\/em>Idle-up1, \u2193<\/em>Idle-up2)<\/td>SB<\/td><\/tr>
    Dual rates (\u2191100%, -85%, \u219375%)<\/em><\/td>SC<\/td><\/tr>
    Rescue Button<\/td>SE<\/td><\/tr>
    Stability mode (auto level) ON\/OFF<\/td>SA<\/td><\/tr>
    Volume control<\/td>S1 slider<\/td><\/tr><\/tbody><\/table>
    Pocket switch assignment<\/figcaption><\/figure>\n\n\n\n

    Other functions<\/h3>\n\n\n\n
      \n
    • Flight timer: 4.5 mins, Haptic countdown at 10 seconds<\/li>\n\n\n\n
    • Voice call on Throttle cut, Throttle active, Flight modes and Stability mode.<\/li>\n<\/ul>\n\n\n\n

      Binding and pre-flight Check<\/h3>\n\n\n\n

      Binding<\/h4>\n\n\n\n
        \n
      1. Ensure batteries of your Helicopter and Transmitter are sufficiently charged<\/li>\n\n\n\n
      2. It is a good idea to remove the main and tail blades of the helicopter to prevent any injury if motors start accidentally.<\/li>\n\n\n\n
      3. Choose the correct model on the TX12.<\/li>\n\n\n\n
      4. Ensure throttle hold is engaged.<\/li>\n\n\n\n
      5. Plug in the battery into the Helicopter and wait for beeps.<\/li>\n\n\n\n
      6. Press and hold BIND<\/strong> button on helicopter. Blue LED<\/mark> will start flashing. Release the BIND<\/strong> button.<\/li>\n\n\n\n
      7. On the Radio, go to Model setup. Press MDL<\/strong> button<\/li>\n\n\n\n
      8. Scroll down to INTERNAL RF<\/strong> section<\/li>\n\n\n\n
      9. Check that the RF Protocol is selected. If not you have chosen the wrong model.<\/li>\n\n\n\n
      10. Press the BIND<\/strong> button<\/li>\n\n\n\n
      11. During binding process, the Blue LED<\/mark> will flash rapidly<\/strong>. Once binding is complete the Blue LED<\/mark> will be steady<\/strong>.<\/li>\n<\/ol>\n\n\n
        \n
        \"\"
        Binding<\/figcaption><\/figure>\n<\/div>\n\n\n

        Pre-flight check<\/h4>\n\n\n\n
          \n
        • The Red LED<\/mark> indicates Auto-level<\/strong> mode status.
          Red LED<\/mark> blinking<\/strong> = Auto-level OFF<\/strong>.
          Red LED<\/mark> steady<\/strong> = Auto-level ON<\/strong>.
          Toggle auto-level switch and see it is switching between Auto-level<\/strong> ON<\/strong> und OFF<\/strong>.<\/li>\n\n\n\n
        • Keep Auto-level OFF<\/strong>.<\/li>\n\n\n\n
        • Move the aileron\/elevator<\/strong> sticks and check that the swash plate is moving correctly (left-right<\/strong> und front-back<\/strong>)<\/li>\n\n\n\n
        • Move the collective<\/strong> pitch stick and check that the swash plate is moving correctly (up<\/strong> & down<\/strong>)<\/li>\n\n\n\n
        • Disengage<\/strong> both throttle hold and throttle hold fail safe<\/strong> switches, give some collective and check that main rotor is spinning<\/strong>.<\/li>\n\n\n\n
        • Engage<\/strong> any one throttle hold<\/strong> and check that main rotor stops<\/strong>.<\/li>\n\n\n\n
        • Engage both<\/strong> throttle holds and check that flight timer resets.<\/li>\n\n\n\n
        • Now you can put the rotor blades back on and do a test flight. Good Luck!<\/li>\n<\/ul>\n\n\n\n

          Model Customization<\/h3>\n\n\n\n

          You can customize the model configuration as per your linking. Please refer to explanation of different settings.<\/p>\n\n\n\n

          Switch Assignment<\/h4>\n\n\n\n

          To change the switch assignments Navigate to Model->Input Page<\/p>\n\n\n

          \n
          \"\"
          Model Input Page<\/figcaption><\/figure>\n<\/div>\n\n\n

          Scroll to the Function whose switch you want to change. e.g. To change rescue mode switch scroll to Rsq input. Press and hold the Scroll wheel and select EDIT.<\/p>\n\n\n

          \n
          \"\"
          Changing Rescue mode switch<\/figcaption><\/figure>\n<\/div>\n\n\n

          Scroll to Source and press the scroll wheel button. Then scroll till you find your desired switch. Press the scroll wheel button to confirm.<\/p>\n\n\n\n

          Throttle curves<\/h4>\n\n\n\n

          For OMP Protocol, there are no throttle curves on the Radio Transmitter as throttle curve is fixed inside the Helicopter. For other protocols, the below curves are used.<\/p>\n\n\n\n

          Curve<\/th>Curve name<\/th>Function<\/th><\/tr><\/thead>
          CV2<\/td>TCn<\/td>Throttle curve for Normal mode<\/td><\/tr>
          CV3<\/td>TC1<\/td>Throttle curve for Idle-up 1<\/td><\/tr>
          CV4<\/td>TC2<\/td>Throttle curve for Idle-up 2<\/td><\/tr><\/tbody><\/table>
          Throttle curves<\/figcaption><\/figure>\n\n\n\n

          Pitch curves<\/h4>\n\n\n\n

          For OMP Protocol, there are no pitch curves on the Radio Transmitter as pitch curves are fixed inside the Helicopter. For other protocols, the below curves are used.<\/p>\n\n\n\n

          Curve<\/th>Curve name<\/th>Function<\/th><\/tr><\/thead>
          CV5<\/td>PCn<\/td>Collective pitch curve for Normal mode<\/td><\/tr>
          CV6<\/td>PC1<\/td>Collective pitch curve for Idle-up 1<\/td><\/tr>
          CV7<\/td>PC2<\/td>Collective pitch curve for Idle-up 2<\/td><\/tr><\/tbody><\/table>
          Pitch curves<\/figcaption><\/figure>\n\n\n\n

          Dead band curve<\/h4>\n\n\n\n

          Older OMP Helicopters have some deadband at center stick at Aileron and Elevator. The dead band curve is mixed with Aileron and Elevator controls to get rid of the dead band. Curve CV12 (DBD) is used as dead band curve.<\/p>\n\n\n\n

          OFS3 controller no longer has the deadband at stick center so we don’t use deadband curve for this configuration.<\/p>\n\n\n\n

          Config file Revision history<\/h4>\n\n\n\n
          v1.3: 2025-10-22
          -added OFS3 FUT for M2 V3 PRO \/ M2 MK2 using Futaba S-FHSS receiver.
          -removed EVO XSR

          v1.2: 2024-06-18
          -Sound fixes in all models

          v1.0: 2024-01-27
          -Initial version
          <\/pre>","protected":false},"excerpt":{"rendered":"
          This guide will show you how to setup your Radiomaster Pocket or any EdgeTX \/ OpenTX Multi-protocol radio for your OMPHobby M1, M2 EVO or M2 V3 Helicopter. If you purchased a RTF Combo or Pocket Radio from us, this setup is already done for you. NOTE: TX12 C2500 supports the following radio protocols (Futaba […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_eb_attr":"","footnotes":""},"class_list":["post-10075","page","type-page","status-publish","hentry"],"jetpack_sharing_enabled":true,"jetpack_shortlink":"https:\/\/wp.me\/Ph9vxs-2Cv","_links":{"self":[{"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/pages\/10075","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/comments?post=10075"}],"version-history":[{"count":0,"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/pages\/10075\/revisions"}],"wp:attachment":[{"href":"https:\/\/originhobbies.com\/de\/wp-json\/wp\/v2\/media?parent=10075"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}